Camo painting your aluminum jon boat?

Paul Crawford

New member
Greetings from the NW,

I am looking for advice on the best way to camo up a 16 ft jon boat. Not so much the colors to choose, but I am looking for what technique people have been successful using. I was wondering about types of paint, and sprayers to use. I don't mind using spray paint but if anyone has any ideas on something better to use I would be grateful.

Thanks
 
I have done a couple . The way i do it is -Ruff sand the boat-sponge on vinegar -rinse- dry-paint all one after the other fast as you can . I used olive drab paint from an army surplus store for aluminum boats and blinds . The vinegar etches the aluminum -rinse-dry-paint before it starts to oxidise . The first boat i did was 12 yrs ago and still looks great . I put the olive drab over the hole boat then spray painted over that with other colors but the olive drab was the base coat .
 
I'd post pics but haven't had the time to learn that yet. :) Lou

Painting an Aluminum or Fiberglass Boat
1. Be sure the boat has been cleaned off well with soap and water to remove all dirt, grease, leaves, grime and all that stuff that accumulates from years of hunting.
2. Lightly solvent wipe things down with a rag and lacquer thinner. This will remove any gasoline, oil or petroleum residues that would mess with your sanding or prevent paint from adhering. When finished with the solvent rag, be sure to let it set out and lose it’s solvents before you put it into a closed container or trash can.
3. Sand the entire boat, as required, to remove and/or scuff all the paint. Be sure to remove any loose paint. When sanding a duck boat, I prefer 80-100 grit. It gives better “tooth” and, after all……..it’ll help with the dulled surface and paint adhesion. Sanding must be taken into the best previously adhered surface in order to have the new coat of paint hold properly.
4. For Aluminum boat-Spot prime any bare aluminum with ASG Primer (or AG Primer), specifically designed for use on “Aluminum, Stainless & Galvanized”. Do not thin AG Primer. A second option would be to prime the entire boat with PPG’s Epoxy Primer.
5. For Fiberglass boat-You can go right to the FME as this is a Primer-Based Paint and will serve as it’s own primer. If you would like, another option would be to prime with PPG-Epoxy Primer and then follow up with FME.
6. Once the primer has dried (AG, PPG or 1st coat of FME), you can base coat the entire boat, inside and out, with the base coat FME (Flat Marine Enamel-oil based) color of your choice. FME is a “primer based” paint and requires no other primer underneath it on a properly prepared surface. You may use a brush, roller or sprayer. When spraying, the best is an airless sprayer though you can thin slightly with a high quality paint thinner for use in a regular air spray gun. If using the air-feed spray gun, we recommend the top-feed, gravity style of gun. It requires less air and less thinning to get a proper pattern. You will also achieve greater success with a couple thinner coats rather than one thick coat. Thinner coats will cure/dry much faster and more thoroughly….thus, more durable. Secret: “thin, you win”.
7. When the base coat is dry (usually overnight in good temps), you may accent with any other FME color you’d like. The options are endless……match your local vegetation.
8. We have several camoflage patterned paint schemes and colors available.
*Our 2-tone Reed Stripe was developed for the cat-tail marshes & flooded corn. Base coat in Starcraft Camo Light Brown (#26) and reed stripe with an automotive striping brush with Starcraft Camo Dark Brown (#27), thinning #27 on the palette as you work. We developed these colors through PPG specifically for us and Starcraft. You can even “green it up” a bit with Dead Grass Green (#28), O/D Green (#35) or some Olive (#18).
*Our Open Water Gray Pattern is very effective for layout hunting. You can base coat the entire boat with Open Water Medium Gray (#33) or Open Water Dark Gray (#34) and allow to dry. Once dry, overstripe with a wave pattern of Open Water Light Gray (#32) by cutting the feed pressure down, reducing the size of your pattern to a small area and reducing the feed rate so it will be easy to control. Move the spray gun around in a lazy “wave”, walk alongside the boat and “wave” the gun to give the pattern you’d like.
We have pictures of these patterns that we can email to you.
9. You can create your own color patterns/schemes with any of the FME colors we have. All the decoy and boat paints are TRUE - FLAT MARINE ENAMELS and work well with each other.
Lock Stock & Barrell, Inc.
123 Avery (shop)
Clinton Twp., MI 48036
Ofc.Ph: (586) 790-2678, Fax: (586) 790-2653, Shop Ph: (586) 465-0339
www.lockstockbarrell.com * duckguylsb@juno.com
 
Back
Top